Instance Propertymigueldeicaza.swiftgodot 0.45.0SwiftGodot

maxSlides

Maximum number of times the body can change direction before it stops when calling moveAndSlide.

final var maxSlides: Int32 { get set }

Mangled symbol

s10SwiftGodot15CharacterBody2DC9maxSlidess5Int32VvpWhat are these?

FNV24: [7S31Q]

Other members in extension

Types

Type members

class var godotClassName: StringName

Instance members

var floorBlockOnWall: Bool
If true, the body will be able to move on the floor only. This option avoids to be able to walk on walls, it will however allow to slide down along them.
var floorConstantSpeed: Bool
If false (by default), the body will move faster on downward slopes and slower on upward slopes.
var floorMaxAngle: Double
Maximum angle (in radians) where a slope is still considered a floor (or a ceiling), rather than a wall, when calling moveAndSlide. The default value equals 45 degrees.
var floorSnapLength: Double
Sets a snapping distance. When set to a value different from 0.0, the body is kept attached to slopes when calling moveAndSlide. The snapping vector is determined by the given distance along the opposite direction of the upDirection.
var floorStopOnSlope: Bool
If true, the body will not slide on slopes when calling moveAndSlide when the body is standing still.
var motionMode: CharacterBody2D.MotionMode
Sets the motion mode which defines the behavior of moveAndSlide. See MotionMode constants for available modes.
var platformFloorLayers: UInt32
Collision layers that will be included for detecting floor bodies that will act as moving platforms to be followed by the CharacterBody2D. By default, all floor bodies are detected and propagate their velocity.
var platformOnLeave: CharacterBody2D.PlatformOnLeave
Sets the behavior to apply when you leave a moving platform. By default, to be physically accurate, when you leave the last platform velocity is applied. See PlatformOnLeave constants for available behavior.
var platformWallLayers: UInt32
Collision layers that will be included for detecting wall bodies that will act as moving platforms to be followed by the CharacterBody2D. By default, all wall bodies are ignored.
var safeMargin: Double
Extra margin used for collision recovery when calling moveAndSlide.
var slideOnCeiling: Bool
If true, during a jump against the ceiling, the body will slide, if false it will be stopped and will fall vertically.
var upDirection: Vector2
Vector pointing upwards, used to determine what is a wall and what is a floor (or a ceiling) when calling moveAndSlide. Defaults to Vector2.UP. As the vector will be normalized it can’t be equal to Vector2.ZERO, if you want all collisions to be reported as walls, consider using .floating as motionMode.
var velocity: Vector2
Current velocity vector in pixels per second, used and modified during calls to moveAndSlide.
var wallMinSlideAngle: Double
Minimum angle (in radians) where the body is allowed to slide when it encounters a slope. The default value equals 15 degrees. This property only affects movement when motionMode is .floating.
func applyFloorSnap()
Allows to manually apply a snap to the floor regardless of the body’s velocity. This function does nothing when isOnFloor returns true.
func getFloorAngle(upDirection: Vector2) -> Double
Returns the floor’s collision angle at the last collision point according to upDirection, which is Vector2.UP by default. This value is always positive and only valid after calling moveAndSlide and when isOnFloor returns true.
func getFloorNormal() -> Vector2
Returns the surface normal of the floor at the last collision point. Only valid after calling moveAndSlide and when isOnFloor returns true.
func getLastMotion() -> Vector2
Returns the last motion applied to the CharacterBody2D during the last call to moveAndSlide. The movement can be split into multiple motions when sliding occurs, and this method return the last one, which is useful to retrieve the current direction of the movement.
func getLastSlideCollision() -> KinematicCollision2D?
Returns a KinematicCollision2D, which contains information about the latest collision that occurred during the last call to moveAndSlide.
func getPlatformVelocity() -> Vector2
Returns the linear velocity of the platform at the last collision point. Only valid after calling moveAndSlide.
func getPositionDelta() -> Vector2
Returns the travel (position delta) that occurred during the last call to moveAndSlide.
func getRealVelocity() -> Vector2
Returns the current real velocity since the last call to moveAndSlide. For example, when you climb a slope, you will move diagonally even though the velocity is horizontal. This method returns the diagonal movement, as opposed to velocity which returns the requested velocity.
func getSlideCollision(slideIdx: Int32) -> KinematicCollision2D?
Returns a KinematicCollision2D, which contains information about a collision that occurred during the last call to moveAndSlide. Since the body can collide several times in a single call to moveAndSlide, you must specify the index of the collision in the range 0 to (getSlideCollisionCount - 1).
func getSlideCollisionCount() -> Int32
Returns the number of times the body collided and changed direction during the last call to moveAndSlide.
func getWallNormal() -> Vector2
Returns the surface normal of the wall at the last collision point. Only valid after calling moveAndSlide and when isOnWall returns true.
func isOnCeiling() -> Bool
Returns true if the body collided with the ceiling on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “ceiling” or not.
func isOnCeilingOnly() -> Bool
Returns true if the body collided only with the ceiling on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “ceiling” or not.
func isOnFloor() -> Bool
Returns true if the body collided with the floor on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “floor” or not.
func isOnFloorOnly() -> Bool
Returns true if the body collided only with the floor on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “floor” or not.
func isOnWall() -> Bool
Returns true if the body collided with a wall on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “wall” or not.
func isOnWallOnly() -> Bool
Returns true if the body collided only with a wall on the last call of moveAndSlide. Otherwise, returns false. The upDirection and floorMaxAngle are used to determine whether a surface is “wall” or not.
func moveAndSlide() -> Bool
Moves the body based on velocity. If the body collides with another, it will slide along the other body (by default only on floor) rather than stop immediately. If the other body is a CharacterBody2D or RigidBody2D, it will also be affected by the motion of the other body. You can use this to make moving and rotating platforms, or to make nodes push other nodes.